How to Charge a Scooter Battery Without a Charger – Introduction, and Charging

As the times are changing, various types of new technologies are surrounding us. Likewise, we are all aware of electric scooters built with rechargeable batteries. 

They tend to work similarly to any other chargeable device. However, the difference today we will be addressing is how to charge a scooter's battery without the help of a charger. 

It might seem impossible, but there are various by the help which you can be able to learn to do it. Hence, keep reading for further details. 

How to perform scooter battery charging with a car? 

The most dreadful feeling one could ever experience is when you start your scooter, but it won't just budge. It can happen for many reasons like the battery is dead and unable to start. 

In such cases, you can always opt for your car to give the scooter a sudden jump start; however, since your car is much stronger than your scooter, it is important to be careful while you are charging it with the help of the car. 

Ways that can help you to charge a scooter battery with a car are mentioned below.

Positioning of the Scooter 

Make sure that the scooter is stood close to the car in a way that it is closer to the car's hood. However, be certain that it is not touching the hood since you will have to put in some effort to stretch the cables between the two vehicles. 

3.2V 20A Low Temp LiFePO4 Battery Cell -40℃ 3C discharge capacity≥70% Charging temperature：-20~45℃ Discharging temperature: -40~+55℃ pass acupuncture test -40℃ maximum discharge rate：3C

READ MORE

Shut off the Engine 

The next step is to turn down the engine for either vehicle, the car or the scooter. It will add to the overall safety of the process.

Positive and Negative ends Identification to be Clear

This step is crucially important as the connection depends on the proper connection of the positive to the positive end. At the same time, the negative terminal is connected to the other negative end. 

Connection of the Clips

Clamp the positive clip on the car's battery, and be careful that it has a fine grip so it will not fall off. Do the same process with the negative terminal. 

Do not start the car and wait for some time. 

Be patient and let the car's battery charge up the scooter. You might need to wait for 20 to 40 minutes, depending on how low the battery your scooter has. Once it is done, remove the clips and kick-start your scooter. 

How to charge a pure electric scooter?

Below are a few basic steps that explain how to charge a pure electric scooter. Make sure to follow them for guaranteed results. 

Low Temperature High Energy Density Rugged Laptop Polymer Battery Battery specification: 11.1V 7800mAh -40℃ 0.2C discharge capacity ≥80% Dustproof, resistance to dropping, anti - corrosion, anti - electromagnetic interference

READ MORE

Plugging of Charger 

The first basic step toward charging a pure electric scooter is to plug the charger into the wall. This is the easiest and safe way of protection against external capacitors. 

It is normal for the charger to get warmed up during the charging. Make sure to set up the charger so that it gets more air exposure. 

Look out for the scooter's connecting port.

Moving further, you must shut down the electric scooter and remove the covering of the connection port that allows charging. 

Be certain that the port and the connector are free of any accumulation of dirt and debris. If it is present, then do clean it before using. 

While connecting the charger to the port, you have to be careful since some of them connect in one way only.  

Wait for some time. 

Once connected, do not disconnect it immediately. Instead, you have to wait for the scooter to charge. For the majority of the chargers, it turns green light when it is fully charged. If you are planning to travel a longer distance, then charge it even after the green light. 

Do not leave the charger plugged in.

We must learn that we should never leave the charger plugged in. Turn off the switch and then unplug the charger from the wall socket. It helps in the prevention of short circuits and the wastage of electricity. 

Where is the charging port on an electric scooter?

The charging port is the main thing that needs to be known when you charge an electric scooter. Usually, the electrical scooter's charging port is at the base of the scooter. It is not hard to identify it. Once you discover it, you can plug the charger in and check whether it is connected or not. 

Some factors you should take good care of while finding the charging port on an electric scooter are as follows.

Use the right charger for the electric scooter since the voltage can vary. 

The use of the right charger is supposed to be considered since the plugs can vary too. 

Once you have securely plugged in the electric scooter charging port, connect it to the main plug. Once you connect it, ideally, the scooter might light up while appearing as a green light sign. This indicates that the current is flowing to the electric scooter, which is being charged. Hence, it would be best if you waited some time till the scooter gets fully charged. 

If you are having problems finding the right place of charging port on the electric scooter, you can take help from the manual guide you might have received while you bought the electric scooter. 

You can also take your electric scooter to the nearest workshop that is professional at such tasks since you do not want to mess up your newly purchased electric scooter for some curiosity. 

Final Remarks:

There are many other ways to charge an electric scooter other than charging it with the car's battery. You can be able to use a laptop's battery, battery isolator, using ups inverter, or solar panels as well. 

Choosing any way of charging depends on how well you execute the plan. Hence, take the help of professional workers around you for a good experience and fewer chances to make major mistakes and blunders that can damage your electric scooter too.